RTS Cstrunk Especificaciones Pagina 49
- Pagina / 104
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
43
3. Tap PGM.
Value: X displays, where X is a number between 5 and 100.
4. To change the selection, press ↓↓ or ↑↑.
The higher the number, the brighter the backlight.
5. Tap PGM.
6. Tap CLR to exit.
7. Run Service Menu, Save Cfg, to store the new setting.
Service Menu, LCP-632 (GPI Option Only)
By default, each LCP-632 that you connect to the KP-632 takes control of level adjustment for the first available group of 16
physical keys that it finds. The first LCP-632 adjusts keys 1-12, which corresponds to the bottom row of keys on the KP-632;
the second LCP-632 adjusts keys 13-24, and so forth (). If you do not want to use an LCP-632 with certain keys, you must
program the KP-632 to skip those keys.
For example, you may not want to use LCP-632s with the KP-632 but do want to use them with an EKP-632. In this case, you
must turn off LCP usage for keys 1-24 as follows:
1. Select LCP-632, and then tap PGM.
1-12: Yes displays. This indicates the first connected LCP-632 attaches to keys 1-12.
2. Tap PGM.
1-12: Skip displays. This indicates the first connected LCP-632 skips keys 1-12 and attaches to the next available row
of keys.
3. Tap ↓↓ to display 13-24: Yes.
4. Tap PGM.
13-24: Skip displays. This indicates the first connected LCP-632 skips keys 13-24 and attaches to the next available
row of keys.
5. Tap CLR to exit.
6. Run Service Menu, Save Cfg, to store the new LCP-632 settings.
Service Menu, Local GPIO (GPI Option Only)
If your KP-632 has an optional Connector Module, you can use this menu item to assign the GPIO inputs and outputs. Inputs
can be assigned to activate intercom keys (including group master keys and a solo key). Outputs can be activated by intercom
keys. Set up inputs and outputs as follows:
Assigning an Input to Activate a Key
1. Select Local GPIO, and then tap PGM.
Input displays.
2. Tap PGM.
GPI Inp #1 displays.
FIGURE 9. LCP-32 correspondence to KP-32 and EKP-32
- USER INSTRUCTIONS 1
- Contents 3
- Introduction 9
- GPI Connector Module 10
- EKP-632 Expansion Keypanel 11
- LCP-632 Level Control Panel 11
- MCP-90 Panel Microphone 12
- Headsets 12
- Installation 13
- Address Switch Setting 14
- Address Setting for Zeus 15
- Address Setting for ADAM CS 15
- Connections 16
- Power Supply Connector 17
- Headset Connector 17
- Panel Microphone Connector 18
- Basic Operation 19
- Intercom Keys and Displays 20
- Listen LED Indication 21
- Intercom Key Operation 22
- Muting the Microphone 23
- Call Waiting Operation 24
- Telephone Operation 25
- KP9X Redial Sequence 26
- KP9X Autodial Sequences 26
- Manual Dialing 27
- Autodial 28
- Display Panel ID 29
- > Tap CLR to quit 29
- 1. Tap the E-PNL key 32
- 3. Tap the PGM key 32
- • Tap COPY 35
- Clearing a Key Assignment 35
- KP-632 Menu System 37
- Menu System, Key Assign Menu 39
- Key Assign Menu, Matrix 40
- Key Assign Menu, Pt-to-Pt 40
- Key Assign Menu, Party Line 40
- Key Option Menu 43
- Key Option Menu, Key Groups 44
- Key Option Menu, Solo 44
- RVON Conn. Menu 45
- Service Menu 45
- Service Menu, Baud Rate 46
- Service Menu, Dim 46
- Service Menu, Disply Dim 46
- Service Menu, Hdst Sel 48
- Service Menu, LCD Bright 48
- Service Menu, Matrix Out 51
- Service Menu, Mic Select 51
- Service Menu, Min Volume 51
- Service Menu, Mod Assign 51
- Service Menu, Output Level 52
- Service Menu, Reset Cfg 53
- Service Menu, Save Cfg 53
- Service Menu, Scr Saver 53
- Service Menu, Sidetone 54
- Service Menu, Snoop Tally 54
- Service Menu, Test Panel 54
- Service Menu, Tone Gen 54
- Specifications 55
- Speaker Amplifier and Speaker 56
- KP9x Display Sequences 63
- KP9x Setup Page Assignment 64
- KP9x Phone Operation 65
- Menu Access 67
- Menu List 68
- Mode 2 Operation 69
- Glossary 71
- Features 77
- Dip Switches 79
- Addresses and the RVON-1 82
- Top Level Menu, Rvon Conn 84
- Basic Network Configuration 87
- Wide Area Network 89
- TABLE 4. Packet Translation 90
- TABLE 5. Packet Translation 90
- IP Addresses 92
- Ping a Computer 93
- RVON Configuration 95
- Network Terminology 96
- • Backcard DB-9 J2 98
- Press Enter 100
- 3. Press Enter 101
Relacionado con productos y manuales para Sistemas de intercomunicación de la puerta RTS Cstrunk
(72 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales