RTS TR-240 Especificaciones Pagina 26
- Pagina / 86
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Status Screen
The Status Screen is the main information screen of the base
station. It displays the status of all the system items:
•
RF Channel of operation
•
Beltpack (full-duplex) Association
•
2-Wire Intercom Settings
•
4-Wire Intercom Settings
•
Auxiliary Input Settings
•
Auxiliary Output Settings
•
Speaker Setting Indicator
RF Channel Selection
The RF Channel Selection screen allows the user to manually
select the RF channel of operation.
Steps to change the RF Channel:
1. From the Status Screen, press <MENU> on the BTR-240
front panel.
2. Using the <UP>/<DOWN> buttons, navigate the cursor to
the “RF Channel” menu option, then press <SET> to select
the menu.
3. The RF Channel Selection Screen is now displayed. The
current RF channel will be flashing indicating that it is ready
to be modified.
4. Use the <UP>/<DOWN> buttons to move to a different RF
channel, or press <MENU> to abort changes and display
current settings.
5. Once the desired RF channel is flashing, press <SET> to
select and activate the channel.
6. After the channel is set, the RF channel will stop flashing
and the LCD will pause while the wireless channel is
reconfigured. The LCD will automatically go back to the
Main Menu screen after this process is complete (return to
Step 2).
NOTE: The RF channel of operation is remembered and
BTR-240 will continue to boot on the same channel
until it is set differently by the user.
Local Headset Interface
Talk Button
Press the <TALK> button on the front panel to enable the audio
path from the local headset microphone. The green LED above
the talk button will illuminate when the audio path is enabled and
will be off when the audio path is disabled. The amount of time
the button is pressed indicates how the audio path is enabled.
Momentary: Press and hold the <TALK> button for longer
than ½ second and the microphone path will be
enabled. When the <TALK> button is released,
the microphone path will be disabled.
Push-to-Latch: Tap the <TALK> button for less than ½ second
and the microphone path will latch and remain
enabled after the button is released. Tap the
button again to turn off the latch and disable the
microphone path.
Channel Select Button
Pressing the <CHANNEL SELECT> button will select the
intercom channel for the local headset. Each press of the button
will cycle through the options: Intercom 1, Intercom 2, and both.
The green LEDs above the button will illuminate for which
intercom channel is currently active for the local headset.
Volume
The local headset volume is controlled from the front panel by
turning the <VOLUME> knob clockwise and counterclockwise
to increase and decrease the volume respectively.
5-2
AuxOut:OffAuxOut:Off
AuxIn:OffAuxIn:Off
RF Ch: 1 2W:OffRF Ch: 1 2W:Off
Assoc: 0 4W:OffAssoc: 0 4W:Off
Figure 5-3
Status Screen
more....more....
Squelch SettingsSquelch Settings
RF ChannelRF Channel
Local HeadsetLocal Headset
->->
Figure 5-4
Main Menu Screen
Channel: 1 2412 MHZChannel: 1 2412 MHZ
RF ChannelRF Channel
Figure 5-5
RF Channel Selection Screen
TAL K
CHANNEL
SELECT
11
22
VOLUME
BTR-240
POWER
menu
set
AuxOut:1&2GAuxOut:1&2G
AuxIn:1&2LAuxIn:1&2L
RF Ch: 6 2W:1&2RF Ch: 6 2W:1&2
Assoc: 0 4W:1&2Assoc: 0 4W:1&2
Local Headset Interface
Figure 5-6
Local Headset Interface
- Operating Manual 1
- Thank you from Bosch 3
- Proprietary Notice 4
- Copyright Notice 4
- Disclaimer 4
- Table of Contents 5
- Section 1 - Introduction 9
- Important Safety Instructions 10
- AuxOut:1&2G 11
- AuxIn:1&2L 11
- RF Ch: 6 2W:1&2 11
- Assoc: 0 4W:1&2 11
- MADE IN USA 12
- Section 3 - TR-240 Beltpack 15
- Operating for the First Time 19
- Battery Charging Instructions 19
- Unpacking 19
- Beltclip Installation 20
- Antenna Connection 20
- Antenna Polarization 20
- Antenna Placement 20
- 24
- Section 5 - BTR-240 Operation 25
- Local Headset Interface 26
- 2-Wire Intercom 28
- TWO CHANNELS OF TELEX OR 29
- CLEAR-COM INTERCOM 29
- (from wired power supply) 29
- TO OTHER 2-WIRE EQUIPMENT 29
- 4-Wire (Matrix) Intercom 31
- Auxiliary Input/Output 32
- Speaker Connector 34
- SpeakerSpeaker 35
- AuxOut:1GAuxOut:1G 36
- AuxIn:OffAuxIn:Off 36
- Figure 5-47 38
- BTR-240 Menu Structure 38
- Section 6 - TR-240 Operation 39
- Mode of Operation 40
- Low Battery Indicator 41
- System Restore 42
- TR-24 beltpacks 42
- Section 7 - System Operation 43
- Wired Mode 44
- Wireless and Wired Mixed-Mode 44
- Master Wireless Mode 45
- TOUR GUIDE 46
- TOUR GROUP 46
- Cell-Type Architecture 47
- Multiple BTR-240s 48
- BTR-240s Linked via Ethernet 49
- BTR-240s Linked via 2-Wire 50
- BTR-240s Linked via 4-Wire 50
- Network Requirements 51
- User Configuration Options 53
- Computer Requirements 53
- Network Configuration 53
- Logging into a Device 54
- Software Version 55
- User Menu Options 56
- Channel Numbers 61
- Wired / Network Interference 64
- Telex Units 66
- RTS Units 66
- Auxiliary Output 67
- Speaker Output 67
- Section 12 - Troubleshooting 69
- Possible Cause 70
- Solution 70
- FCC and Industry Canada 73
- EU Compliance Information 74
- Table 13-1 75
- Table 13-2 76
- EU Declaration of Conformity 77
- Model Number 79
- Part Number 79
- Description 79
- Section 15 - Glossary 83
Relacionado con productos y manuales para Sistemas de intercomunicación de la puerta RTS TR-240
(18 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales