RTS TR-240 Especificaciones descargar pdf (Pagina 19)

Unpacking

Unpack the RTS System and retrieve the Package Contents list.

Verify that all contents have been received according to the

Package Contents list. Also, ensure that none of the system

components have acquired any damage.

Contact the shipper or dealer immediately if anything is damaged

or missing.

Operating for the First Time

After unpacking, ensure that all the BTR-240 and TR-240

devices do not have the same IP address. If so, refer to the "User

Configuration" section in this operating manual for instructions

on how to change the IP address.

Prior to use, the TR-240 beltpacks should always have their

batteries fully charged. Refer to the "Battery Charging

Instructions" in this section of the operating manual.

The capacity, or number of allowable full-duplex beltpacks, is

dependent upon the environment in which the system is used.

When operating for the first time, it is recommended that only a

few beltpacks are used to verify the system operation. Once

communication has been verified with a few beltpacks, more can

be added.

After system operation has been initially verified, it is strongly

recommended that the user login to each of the devices and

change the audio encryption key, SSID, wireless encryption key,

or all, to something different from the factory defaults. This will

ensure that the system is unique and other nearby system devices

cannot connect and communicate. Refer to the "User

Configuration" section in this operating manual for instructions

to change these settings.

Battery Installation and Removal

The TR-240 features a removable and rechargeable Li-Ion

battery pack (Model: BP-240) that requires low maintenance and

superior performance for a wide range of temperatures. Battery

care and maintenance is further reviewed in Section 9.

The BP-240 battery pack is inserted into the TR-240 beltpack by

sliding the battery in from the side.

Figure 4-1

Inserting Battery into TR-240

The battery pack is designed to fit only one way in the TR-240

beltpack. Be certain that the gold contacts on the battery align

with the contacts on the beltpack. When inserted correctly, the

battery locking mechanism will “click” and the battery will not be

able to slide out.

To remove the battery pack, simply slide the battery locking

mechanism as indicated by the arrow to release the lock. At this

point, the battery will be free to slide out and be removed from the

beltpack

Figure 4-2

Unlocking Battery Mechanism on TR-240

Battery Charging Instructions

Prior to use, the BP-240 battery packs should be fully charged.

The battery packs can be charged either directly in the TR-240

beltpack via supplied wall adapter, or by using the CHG-240

four-bay quick charger.

NOTE: Battery packs should always be charged in a room

temperature location.

Beltpack Direct Charge

A beltpack direct charge will require approximately 8 full hours

to completely charge a dead battery. Once charging is complete,

beltpacks may be left charging indefinitely. A beltpack can also

be used while charging via beltpack direct charge. This is

especially common for beltpacks in wired mode.

1. Ensure the TR-240 is in the “OFF” position.

2. Plug the AC end of the supplied 12VDC wall adapter into a

standard AC wall outlet. Plug the charge connector into the

charge jack on the bottom of the beltpack.

3. The Charge Light on the bottom of the TR-240 indicates the

battery charge status.

RED = Charging in progress

GREEN = Charging is done

NOTE: Batteries may not charge completely if the beltpack is

being used while charging. Ensure that the beltpack is

in the “OFF” position to completely charge the battery

pack.

Section 4 - Initial Equipment Setup

4-1

Push

Down

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 85 86

Comentarios a estos manuales

Sin comentarios

RTS TR-240 Especificaciones Pagina 19

Comentarios a estos manuales

Relacionado con productos y manuales para Sistemas de intercomunicación de la puerta RTS TR-240