RTS XCP-48-RJ45 Manual de usuario Pagina 23
- Pagina / 107
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
19
Status, GPI Output
GPI Output displays the status of each GPI Output assigned in the system. GPI output is similar to the GPI Input, except
instead of triggering an action on the intercom, the intercom is programmed to perform a function as a result of an action on
the intercom. For example, when a port is connected to a 2-way radio, the radio is normally in receive mode. Use a GPI Output
to trigger the transmitter whenever anyone talks to the port.
1. Turn the ENC1 knob to scroll to Status.
2. When Status is displayed, tap the ENC1 knob.
AZedit displays.
3. Turn the ENC1 knob to scroll to GPI Output.
4. Tap the ENC1 knob.
1-64 displays.
5. Turn the ENC1 knob to scroll through the GPI Output assignments.
Status, Keypanels
The Keypanel menu displays the status of each of the keypanels in the Cronus system.
1. Turn the ENC1 knob to scroll to Status.
2. When Status is displayed, tap the ENC1 knob.
AZedit displays.
3. Turn the ENC1 knob to scroll to Keypanels.
4. Tap the ENC1 knob.
The status is shown for keypanels 1 & 2.
5. Turn the encoders to display the status of the other keypanels (up to 32 keypanels per frame).
The status will display as OK or blank.
Status, Links
The Links menu displays the status of the links (connections) between frames, see “Cronus System Diagram and Frame
Cabling” on page 11. Each frame in the system has two links, Link A and Link B. Link A on each frame connects to the
preceding frame (connecting to Link B).
1. Turn the ENC1 knob to scroll to Status.
2. When Status is displayed, tap the ENC1 knob.
AZedit displays.
3. Turn the ENC1 knob and scroll to Links.
4. Tap the ENC1 knob.
5. Turn the ENC1 knob to scroll through the Links.
You should check the status of the Frame Clock and the Link to each frame. This is good for diagnostic troubleshooting.
NOTE: Frame 1 (Master) will only show the Frame 2 status because it only connects to one other Cronus frame.
Version, Intercom
The Version, Intercom menu, displays the firmware version that is current on the intercom.
NOTE: For Firmware upgrades, contact Telex Customer Service. The Cronus Firmware can be upgraded through AZedit.
See “Download Firmware for Cronus” on page 29, for more information.
- Digital Intercom Matrix 1
- Contents 3
- POSSIBLE PITFALL WITH 4
- TELCO BACKCARD 4
- Introduction 7
- Cronus Gain Structure 10
- Specifications 11
- Connections 11
- DIP Switch Settings 14
- Cronus from the inside 15
- Cronus Menu Structure 19
- Status, AZedit 21
- Status Menu 21
- Status, Crosspoints 22
- Status, Frames 22
- Status, GPI Input 22
- Status, GPI Output 23
- Status, Keypanels 23
- Status, Links 23
- Version, Intercom 23
- Menu Access 24
- Cronus and AZedit 25
- Accessing Vox 26
- Threshold 27
- Download Cronus License File 30
- Ethernet Setup for Cronus 31
- Download Firmware for Cronus 33
- Final Assembly Drawing 37
- Final Assembly 38
- FIGURE 43. Wiring Diagram 40
- Features 42
- J10, J11 44
- Pin 1 44
- RVON-C Backcard 45
- RVON-C Backplate 45
- J1 Serial 45
- J2 Serial 45
- Software Requirements 46
- Switches and Connections 47
- 1. Open AZedit 60
- 6. Click Open 61
- 7. Click Begin Download 61
- 8. Click OK 61
- RVON-C System Diagram 62
- Basic Network Configuration 63
- WIDE AREA NETWORK 64
- TABLE 1. Packet Translation 65
- Table 2. Packet Translation 66
- IP ADDRESSES 67
- Ping a Computer 68
- 3. Press Enter 69
- RVON Configuration 70
- Network Terminology 71
- RVON-C Card 73
- Serial Port Programming 73
- RVON-C Boot Download 74
- Access Serial Command Mode 76
- Serial Command Table 77
- TABLE 4. Serial Command Table 78
- Codec Specifications 79
- RVON-C Default Setup 80
- RVON-C Quick Start 81
- Configure the RVON-C Card 83
- Breakout Panels 87
- XCP-32-DB9 Breakout Panel 88
- J3 17-24 89
- J4 25-32 89
- XCP-48-RJ45 Breakout Panel 90
- XCP-48-Telco Breakout Panel 92
- Telco Backcard 93
- Telco Connector J1, J4 93
- Cronus Master Controller Card 95
- 9030-7785-000 95
- RVON Trunking Connections 99
- Figure 12: RVON-16 Trunking 106
Relacionado con productos y manuales para Sistemas de intercomunicación de la puerta RTS XCP-48-RJ45
(106 paginas)
(36 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales