RTS XCP-48-RJ45 Manual de usuario Pagina 20
- Pagina / 107
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
16
5. Tap the ENC1 knob.
Auto Config displays. You can either have auto-config set the frame or you can manually set the frame ID by turning
the ENC1 knob to scroll through the Frame ID options.
6. Turn the ENC1 knob to scroll through the choices (Auto Config, Frame ID 2, Frame ID 3, or Frame ID 4).
7. Tap the ENC1 knob to make your selection.
IFB Program INs
I/O Gains
I/O Gain is the level of audio at which you hear and are heard. There may be occasions where you need to adjust the gain for
some specific intercom port. For example, a belt pack operator may want to monitor a party line, but at a lower level than the
normal intercom volume. Or, a beltpack operator may want to listen to the background music coming from some intercom
input port, but at a reduced level.
To set Gain from the front panel of Cronus, do the following:
1. Tap the ENC1 knob.
Configure appears.
2. Tap the ENC1 knob.
Frame ID appears.
3. Turn the ENC1 knob to I/O Gains.
4. Tap the ENC1 knob.
Select Port appears. There are 32 ports from which to select.
5. Turn the ENC1 knob to the port you want.
6. Tap the ENC1.
IN Gain and OUT Gain appears.
7. Use the ENC1 knob to adjust the IN Gain.
OR
Use the ENC2 knob to adjust the OUT Gain.
NOTE: You can change the gain levels in AZedit and see the results on Cronus almost immediately. For
more information on gain levels, see Figure 32 on page 6.
Vox Thresholds
Vox Threshold is the level of audio at which a channel becomes active. When the threshold is set, the microphone will not
turn on until the set audio level hits the set threshold. This prevents a channel from staying active when no one is around in a
high activity area.
To set and enable Vox Thresholds from the front panel of Cronus, do the following:
1. Tap the ENC1 knob.
Configure appears.
2. Tap the ENC1 knob.
Frame ID appears.
3. Turn the ENC1 knob to Vox Thresholds
Threshold appears.
4. Tap the ENC1 knob.
Select Port appears.
5. Turn the ENC1 knob to the port to be set.
You can set the thresholds on all 32 ports on the Cronus.
6. Tap the ENC1 knob to select the port.
7. Turn the ENC1 knob to set the threshold level (-127 dB to 0.0 dB)
- Digital Intercom Matrix 1
- Contents 3
- POSSIBLE PITFALL WITH 4
- TELCO BACKCARD 4
- Introduction 7
- Cronus Gain Structure 10
- Specifications 11
- Connections 11
- DIP Switch Settings 14
- Cronus from the inside 15
- Cronus Menu Structure 19
- Status, AZedit 21
- Status Menu 21
- Status, Crosspoints 22
- Status, Frames 22
- Status, GPI Input 22
- Status, GPI Output 23
- Status, Keypanels 23
- Status, Links 23
- Version, Intercom 23
- Menu Access 24
- Cronus and AZedit 25
- Accessing Vox 26
- Threshold 27
- Download Cronus License File 30
- Ethernet Setup for Cronus 31
- Download Firmware for Cronus 33
- Final Assembly Drawing 37
- Final Assembly 38
- FIGURE 43. Wiring Diagram 40
- Features 42
- J10, J11 44
- Pin 1 44
- RVON-C Backcard 45
- RVON-C Backplate 45
- J1 Serial 45
- J2 Serial 45
- Software Requirements 46
- Switches and Connections 47
- 1. Open AZedit 60
- 6. Click Open 61
- 7. Click Begin Download 61
- 8. Click OK 61
- RVON-C System Diagram 62
- Basic Network Configuration 63
- WIDE AREA NETWORK 64
- TABLE 1. Packet Translation 65
- Table 2. Packet Translation 66
- IP ADDRESSES 67
- Ping a Computer 68
- 3. Press Enter 69
- RVON Configuration 70
- Network Terminology 71
- RVON-C Card 73
- Serial Port Programming 73
- RVON-C Boot Download 74
- Access Serial Command Mode 76
- Serial Command Table 77
- TABLE 4. Serial Command Table 78
- Codec Specifications 79
- RVON-C Default Setup 80
- RVON-C Quick Start 81
- Configure the RVON-C Card 83
- Breakout Panels 87
- XCP-32-DB9 Breakout Panel 88
- J3 17-24 89
- J4 25-32 89
- XCP-48-RJ45 Breakout Panel 90
- XCP-48-Telco Breakout Panel 92
- Telco Backcard 93
- Telco Connector J1, J4 93
- Cronus Master Controller Card 95
- 9030-7785-000 95
- RVON Trunking Connections 99
- Figure 12: RVON-16 Trunking 106
Relacionado con productos y manuales para Sistemas de intercomunicación de la puerta RTS XCP-48-RJ45
(106 paginas)
(36 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.075 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales