RTS XCP-24 Manual de servicio Pagina 46
- Pagina / 114
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
6-8 KP-632 User Manual
2 Tap any keys where you want to add a chime tone. Both LEDs will light red for the selected
keys.
3 Tap CLR to exit.
4 Run Service Menu, Save Cfg, to store Chime settings.
Note
The chime option will continue on a key even if you change the key assignment.
Removing the chime option from a key
Repeat the procedure to add chime, but tap any keys where the LEDs are lit red to turn them off.
Run Save Cfg to store the changes.
Key Option Menu, Key Groups
You can set up a key group, so that when you activate one key (the master key) all keys in the
group will activate. Up to 4 key groups can be set up.
1 Select
Key Groups
, then tap PGM.
2
Group 1
displays. To select a different group, press ↓↓ or − − .
3 Tap PGM.
4
Tap Master
displays. The master key is the key that you will press to activate the group.
5 Tap the intercom key that you want to use as the master. Both LEDs next to the key will light
red.
6 After you select the master key,
Tap Slaves
displays. Slave keys are the keys that will activate
along with the master key.
7 Tap one or more keys to select them as slave keys. Both LEDs will light green for each key that
is selected. You can tap a key again to remove it from the key group.
8 Tap CLR when finished.
9 Activating the master key should now cause it and all slave keys to activate. The LEDs for
each key will activate according to the current key assignment for that key.
10Run Service Menu, Save Cfg, to store Key Group settings.
Note
Key group settings will continue on keys even if you change the key assignments.
Clearing a key group
1 Select
Key Groups
, then tap PGM.
2
Group 1
displays. To select a different group, press ↓↓ or −− .
3 Tap PGM.
4
Tap Master
displays.
5 Tap the current master key. The LEDs will remain lit red.
6 After you tap the master key,
Tap Slaves
displays.
7 Tap all the keys where the LEDs are lit green. This will turn the LEDs off.
8 Tap CLR when finished.
9 The key group is now cleared.
10Run Service Menu, Save Cfg, to store the cleared key group setting.
- USER INSTRUCTIONS 1
- PROPRIETARY NOTICE 2
- COPYRIGHT NOTICE 2
- UNPACKING AND INSPECTION 2
- WARRANTY INFORMATION 2
- CUSTOMER SUPPORT 2
- RETURN SHIPPING INSTRUCTIONS 3
- TABLE OF CONTENTS 5
- Telephone Operation 4-1 6
- KP-632 Menu System 6-1 6
- Specifications 7-1 7
- Mode 2 Operation 10-1 8
- Glossary 11-1 8
- Appendix 12-1 8
- NTRODUCTION 9
- GPI/Connector Module 10
- Headsets 11
- EKP-632 Expansion Keypanel 11
- LCP-632 Level Control Panel 11
- MCP-90 Panel Microphone 11
- 1-4 KP-632 User Manual 12
- NSTALLATION 13
- Address Switch Setting 14
- Address Setting for Zeus 15
- Address Setting for ADAM CS 15
- CS Intercom Systems 16
- Connections 17
- Power Supply Connector 18
- Headset Connector 18
- Panel Microphone Connector 19
- 2-8 KP-632 User Manual 20
- PERATION 21
- Intercom Keys and Displays 22
- Intercom Key Operation 23
- 3-4 KP-632 User Manual 24
- Muting the Microphone 25
- Call Waiting Operation 25
- 3-6 KP-632 User Manual 26
- ELEPHONE 27
- KP9X Redial Sequence 28
- KP9X Autodial Sequences 28
- Manual Dialing 29
- Autodial 30
- ROGRAMMING 31
- Test Keys and Displays 32
- 1 Tap the E-PNL key 33
- 3 Tap the PGM key 33
- General Procedure 34
- 1 Tap COPY 36
- Clearing a Key Assignment 37
- 5-8 KP-632 User Manual 38
- KP-632 M 39
- 6-2 KP-632 User Manual 40
- MENU SYSTEM, KEY ASSIGN MENU 41
- Key Assign Menu, Matrix 42
- Key Assign Menu, Pt-to-Pt 42
- Not Avail 43
- Key Assign Menu, Key Gain 44
- Key Assign Menu, Reset Vols 44
- KEY OPTION MENU 45
- Key Option Menu, Key Groups 46
- Clearing a key group 46
- SERVICE MENU 47
- Service Menu, Disply Dim 48
- Service Menu, DSP Func 48
- Filtering 49
- Metering 49
- Service Menu, Hdst Sel 50
- Service Menu, LCD Bright 51
- Service Menu, LCP-632 51
- Service Menu, Local GPIO 52
- Service Menu, Matrix Out 53
- Service Menu, Mic Select 54
- Service Menu, Min Volume 54
- Service Menu, Mod Assign 54
- Service Menu, Output Level 55
- Service Menu, Reset Cfg 56
- Service Menu, Save Cfg 56
- Service Menu, Sidetone 56
- Service Menu, Test Panel 56
- Service Menu, Tone Gen 56
- PECIFICATIONS 57
- Headset Connector (Dynamic) 58
- Power Input Connector 59
- Connectors 59
- Expansion Connector 59
- LCP Connector 60
- Relay 1 & 2 Out 60
- Relay 3 & 4 Out 60
- OC 1 & 2 Out (J2) 61
- Foot Switch/Speaker 62
- EFERENCE 63
- KP9X PHONE OPERATION 64
- KP9X Dial Sequence 65
- 8-4 KP-632 User Manual 66
- Tone Gen 68
- 9-2 KP-632 User Manual 68
- Sidetone* 68
- Test Panel 68
- 9-4 KP-632 User Manual 70
- 10-2 KP-632 User Manual 72
- S ECTION 73
- KP-632 User Manual 74
- 11-4 KP-632 User Manual 76
- Special List 76
- Stacked Key 76
- Talk Level 1 77
- Talk Level 2 77
- Trunking 77
- 11-6 KP-632 User Manual 78
- RTS Voice Over Network 79
- Family of Keypanels 79
- ADDENDUM 79
- 2 RVON-1 User Manual 80
- RVON-1 User Manual 3 81
- 4 RVON-1 User Manual 82
- RVON-1 User Manual 5 83
- 6 RVON-1 User Manual 84
- Introduction 85
- Switch 1: Reserved 86
- RVON-1 User Manual 9 87
- RVON-1 Ethernet Connection 88
- CSI Connection 88
- TOP LEVEL MENU, RVON CONN 91
- The download begins 96
- Appendix A 97
- Basic Network Configuration 97
- Table 1. Packet Translation 99
- Table 2. Packet Translation 99
- 22 RVON-1 User Manual 100
- TELNET <IP Address> 107
- A prompt appears 108
- An MXP prompt appears 108
- RVON-1 User Manual 33 111
- RVON-1 User Manual 35 113
Relacionado con productos y manuales para Sistemas de intercomunicación de la puerta RTS XCP-24
(12 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.026 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales